Tripp Lite SmartPro 2200VA 120V SMART2200RM2U - Refurbished

OUTPUT

Output Volt Amp Capacity (VA)

2200

Output kVA capacity (kVA)

2.2

Output Watt Capacity (watts)

1920

Output kW capacity

1.92

Output power factor

0.87

Nominal Output Voltage(s) Supported

120V

Frequency compatibility

60 Hz

Output voltage regulation (line mode)

-14%, +6%

Output voltage regulation (Battery mode)

+/- 5%

Built-in UPS output receptacles

4 5-15R outlet(s); 4 5-15/20R outlet(s)

Built-in controllable switched load banks

Two switchable single-outlet load banks

Output AC waveform (AC mode)

Pure Sine wave

Output AC waveform (battery mode)

Pure Sine wave

INPUT

Rated input current (at maximum load)

16A (120V)

Nominal Input Voltage(s) Supported

120V AC

UPS input connection type

5-20P

Input circuit breaker

20A

UPS Input cord length (ft.)

10

UPS Input cord length (m)

3

Recommended Electrical Service

20A 120V

Phase

Single-Phase

BATTERY

Full load runtime (minutes)

4.5 min. (1920w)

Half load runtime (minutes)

12 min. (960w)

DC system voltage (VDC)

48

Battery recharge rate (included batteries)

Less than 4.5 hours from 10% to 90%

Replacement battery cartridge (internal UPS battery replacement)

RBC94-2U

Battery Access

Front panel battery access door

Battery replacement description

Hot-swappable, user replaceable batteries

VOLTAGE REGULATION

Voltage regulation description

Automatic voltage regulation (AVR) maintains line power operation with an input voltage range of 83 to 145

Overvoltage correction

Input voltages between 127 and 145 are reduced by 12%

Undervoltage correction

Input voltages between 108 and 96 are boosted by 12%

Severe undervoltage correction

Input voltages between 83 and 95 are boosted by 24%

LEDS ALARMS & SWITCHES

Front panel LCD display

Front panel LCD information and configuration screen offers detailed UPS and site power status and operating data, plus configuration of voltage, operating mode, alarm function and a variety of additional options (see manual for detailed LCD configuration and monitoring options)

Alarms

Audible alarm indicates UPS startup, power-failure, low-battery, overload, UPS fault and remote shutdown conditions

Alarm cancel operation

Power-fail alarm can be temporarily silenced using alarm-cancel switch; silent mode alarm configuration option available

Switches

3 pushbutton switches control OFF / ON power status, MODE selection and MUTE / ENTER control functions

SURGE / NOISE SUPPRESSION

UPS AC suppression joule rating

570

UPS AC suppression response time

Instantaneous

EMI / RFI AC noise suppression

Yes

PHYSICAL

Installation form factors supported with included accessories

4 post 19 inch rackmount (mounting rail kit included)

Installation form factors supported with optional accessories

2 post rackmount (2POSTRMKITWM); Wallmount (2POSTRMKITWM); Tower (2-9USTAND)

Primary form factor

Rackmount

UPS / Power Module dimensions in primary form factor (height x width x depth / inches)

3.5 x 17.5 x 19.5

UPS / Power Module dimensions in primary form factor (height x width x depth / cm)

8.9 x 44.4 x 49.4

Rack Height

2U

Secondary form factor

Tower (requires 2-9USTAND)

UPS / Power Module weight (lbs)

57.6

UPS / Power Module weight (kg)

26.1

UPS Shipping dimensions (height x width x depth / inches)

7.9 x 21.7 x 24.2

UPS Shipping dimensions (height x width x depth / cm)

20.1 x 55.1 x 61.5

Shipping weight (lbs)

57.6

Shipping weight (kg)

26.2

Cooling method

Fan

UPS housing material

Steel

ENVIRONMENTAL

Operating Temperature Range

+32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius

Storage Temperature Range

+5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius

Relative Humidity

0 to 95%, non-condensing

AC mode BTU / hr. (full load)

306

COMMUNICATIONS

Communications interface

USB (HID enabled); DB9 Serial; EPO (emergency power off); Slot for SNMP/Web interface

Network monitoring port description

Supports detailed monitoring of UPS and site power conditions

Communications cable

USB, DB9 and EPO cabling (NOT INCLUDED)

WatchDog compatibility

Supports Watchdog application, OS and hard-reboot restart options for remote applications

LINE / BATTERY TRANSFER

Transfer time

5 milliseconds (AC to battery mode), 1 millisecond (Battery to AC mode)

Low voltage transfer to battery power (setpoint)

83

High voltage transfer to battery power (setpoint)

145

SPECIAL FEATURES

Grounding lug

Back panel grounding lug

Cold Start (startup in battery mode during a power failure)

Cold-start operation supported

High availability UPS features

Hot swappable batteries

Green & high efficiency features

Greater than 95% efficiency - GREEN UPS; Individually controllable load banks

CERTIFICATIONS

UPS Certifications

Tested to UL1778 (USA); Tested to CSA (Canada); Tested to NOM (Mexico); Meets FCC Part 15 Category A (EMI)